{
  "schema_version": 3,
  "scope": "Selected ordinary explanations from the investigation and earlier component reviews. Earlier reviews establish methodological context, not numerical evidence for this motor. These are not internal reasoning or a transcript of agent debate.",
  "chronology_note": "The earlier reviews were recorded on 9 November and the public-reference calculations on 11 November 2026. Mass and fault calculations overlapped. Notes appear beside the relevant evidence.",
  "episodes": [
    {
      "id": "equal-torque-mass",
      "title": "Why the winding belongs in the mass balance",
      "anchor": "fig1",
      "excerpts": [
        {
          "label": "Earlier general review of component mass",
          "text": "Magnet and magnetic-circuit changes can enable lower surrounding steel, copper, or cooling mass even when current or copper heating binds.",
          "recorded_at": "2026-11-09T19:51:52.923Z",
          "type": "verbatim excerpt, Markdown emphasis omitted",
          "agent": "Independent component reviewer",
          "model": "Gemini 4 Argon",
          "model_id": "google/gemini-4-argon",
          "model_attribution": "Model recorded on the original assistant message and confirmed against its provider response."
        },
        {
          "label": "Original magnet with the alternative ring",
          "text": "If we retain the existing winding instead, that thicker-magnet alternative produces approximately 19 W less copper heat at the reference resistance, with no direct modeled mass saving. We cannot count both the full heat benefit and the copper removal.",
          "recorded_at": "2026-11-11T20:26:50.128Z",
          "type": "verbatim excerpt, Markdown emphasis omitted",
          "agent": "Lead investigation agent",
          "model": "GPT 6 Astra",
          "model_id": "gpt-6-astra",
          "model_attribution": "Model recorded in matching Codex turn metadata."
        }
      ],
      "revision": "The alternative ring lets us use less copper or generate less heat. The ledger counts the copper reduction at equal loss. Cooling and installation still have to fit within the remaining mass budget.",
      "evidence": [
        {
          "href": "evidence/direct_equal_torque_ledger.csv",
          "label": "Direct equal-torque ledger",
          "locator": "radial_sus_ring_1.0_t1.0_target300"
        },
        {
          "href": "evidence/equal_torque_all_five.csv",
          "label": "Ring and winding comparison"
        }
      ]
    },
    {
      "id": "fault-assumption",
      "title": "Why peak current alone cannot set the magnet requirement",
      "anchor": "fig4",
      "excerpts": [
        {
          "label": "After solving the fault through time",
          "text": "The five-rotor comparison is showing why a single current multiplier was inadequate. The field distribution and which magnet locations experience the peak matter as much as the peak current.",
          "recorded_at": "2026-11-11T19:22:38.894Z",
          "type": "verbatim excerpt, Markdown emphasis omitted",
          "agent": "Lead investigation agent",
          "model": "GPT 6 Astra",
          "model_id": "gpt-6-astra",
          "model_attribution": "Model recorded in matching Codex turn metadata."
        },
        {
          "label": "Earlier review of field exposure in a different motor",
          "text": "It is an exposure diagnostic, not a defeat condition; I had overstated it as one. Whether the magnet survives needs a measurement of the finished part's hot recoil and history after machining and coating.",
          "recorded_at": "2026-11-09T01:33:31.233Z",
          "type": "verbatim excerpt, Markdown emphasis omitted",
          "agent": "Independent component reviewer",
          "model": "Claude Opus 5.5",
          "model_id": "claude-opus-5-5",
          "model_attribution": "Model recorded on the original assistant message and confirmed against its provider response."
        }
      ],
      "revision": "We now retain each magnet location’s worst exposure before ranking the whole magnet. This corrects the field statistic, but calculated exposure is not measured irreversible damage.",
      "evidence": [
        {
          "href": "evidence/fault_summary.csv",
          "label": "Material-history and instantaneous field results"
        },
        {
          "href": "/lab-notebook/001/record/CLOSURE.md",
          "label": "Numerical checks and limits"
        }
      ]
    },
    {
      "id": "existing-supply",
      "title": "Why we paused the proposed materials experiment",
      "anchor": "supply",
      "excerpts": [
        {
          "label": "The proposed direction",
          "text": "The strongest hypothesis worth testing is a thin, HRE-free finished magnet that retains high hot remanence while gaining demagnetization resistance through grain-boundary processing.",
          "recorded_at": "2026-11-11T20:17:27.842Z",
          "type": "verbatim excerpt, Markdown emphasis omitted",
          "agent": "Lead investigation agent",
          "model": "GPT 6 Astra",
          "model_id": "gpt-6-astra",
          "model_attribution": "Model recorded in matching Codex turn metadata."
        },
        {
          "label": "After checking existing supply",
          "text": "Existing HRE-free grades are credible enough that we should pause the proposed materials experiment. Our three-specimen comparison did not establish an industry capability gap. I moved too quickly from that comparison to grain-boundary development.",
          "recorded_at": "2026-11-11T20:26:50.128Z",
          "type": "verbatim excerpt, Markdown emphasis omitted",
          "agent": "Lead investigation agent",
          "model": "GPT 6 Astra",
          "model_id": "gpt-6-astra",
          "model_attribution": "Model recorded in matching Codex turn metadata."
        }
      ],
      "revision": "The next question became whether an available finished magnet, with a different ring and winding, could deliver the required performance. Hot finished-part data can distinguish a need for material development from a finishing or integration problem.",
      "evidence": [
        {
          "href": "evidence/SUPPLIER_UPDATE.md",
          "label": "Supplier evidence and limitations",
          "locator": "Existing supply changes the next question"
        }
      ]
    }
  ]
}
